Home    RC Electronica   BEC  Graupner 4176.XT60 Akkuweiche dual BEC PRX-5A HV stab XT60 Pakket
Graupner 4176.XT60 Akkuweiche dual BEC PRX-5A HV stab XT60 Pakket

Graupner 4176.XT60 Akkuweiche dual BEC PRX-5A HV stab XT60 Pakket


Instelbaar voltage (5,3 V / 5,9 V / 7,4 V) powerBEC 5Amp Stabil


Tags


61.99

€ 59.90


Op voorraad


Artikelcode: 4176.XT60

Graupner 4176.XT60 Akkuweiche dual BEC PRX-5A HV stab  XT60  Pakket


  • Productinformatie
  • ANDERE BEC hardware

Perfecte en prijsbewuste Akkuweiche-BEC voedingsgarantie voor uw ontvanger en servo's.
Diverse voltage en gebruikers instellingen mogelijk.
Toebehoren diverse stekkersystemen.
Voor gebruik van 1 of 2 ontvangerpacks



PRX-5A HV (Power for Receiver)
A highly developed, stabilised receiver power supply with intelligent power management.
This unit guarantees a stabilised, user-selectable power supply for the receiver, with the aim of further enhancing the reliability of the power supply.
It is suitable for use with a wide range of receiver batteries, and therefore forms a simple means of providing a reliable power supply in a very wide range of models.
If the battery voltage should collapse while the system is operating - even if only for a brief period - the unit stores the event and indicates it subsequently.
The user is therefore warned of an inadequate or even failing receiver battery, and can implement suitable counter-measures in good time.
If the PRX is switched on via the safety on/off switch, it remains switched on until it is explicitly switched off even if the switch is defective.

  • For use with one or two receiver batteries
  • Simultaneous discharging when used with two batteries
  • For use with five-cell or six-cell NiMH batteries or two-cell LiPo or LiFe batteries, GRAUPNER/JR G3.5, G2 and BEC connectors
  • Four user-selectable output voltage levels for powering the receiver (5,3 V / 5,9 V / 7,4 V)
  • Dual receiver power supply for maximisedsecurity
  • Two LEDs indicate the operational state of Battery 1 and Battery 2 separately
  • Ultra-bright LEDs for good legibility even in poor light conditions
  • Integral high-quality safety On / Off switch
  • Heavy-duty construction for handling high currents
  • Low-profile switch and LEDs to avoid spoiling the model's appearance and characteristics
  • In-line arrangement of mounting lugs, LEDs and switch for simple installation using the drilling template supplied
  • Battery types: 2-cell Lipo
  • 2-cell LiFe
  • 2-cell LiIon
  • 5-cell NiMH/NiCd
  • 6-cell NiMH/NiCd
  • Input voltage: 4V to 9V (stable operation is not possible below 4V)
  • Max. input voltage: 12V
  • Biascurrent: approx. 0.3µA (switched off)
  • Max. continuous current: approx. 5 A (for 1 min. for LiPo 5.9V)
  • Max. peak current: approx. 15A (for 1 sec. for LiPo 5.9V)
  • Max. peak current: approx. 25A (for 100 msec. for LiPo 5.9V)
  • The data refer to operation of the PRX without active cooling e.g. by overflowing air. With cooling, the values are even higher
  • Weight approx. 35g